TOSHIBA MK6015MAP
/dev/hda:
Timing buffer-cache reads: 64 MB in 0.55 seconds =116.36 MB/sec
Timing buffered disk reads: 32 MB in 2.44 seconds =13.11 MB/sec
bash-2.05# cat /proc/ide/hda/model
FUJITSU MPG3409AT E
/dev/hda:
Timing buffer-cache reads: 128 MB in 1.04 seconds =123.08 MB/sec
Timing buffered disk reads: 64 MB in 2.35 seconds = 27.23 MB/sec
bash-2.05# cat /proc/ide/hdc/model
IBM-DPTA-372050
/dev/hdc:
Timing buffer-cache reads: 128 MB in 1.01 seconds =126.73 MB/sec
Timing buffered disk reads: 64 MB in 2.94 seconds = 21.77 MB/sec
disk
bash: hddparm: command not found
Maxtor 91020U3
# /sbin/hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.88 seconds =145.45 MB/sec
Timing buffered disk reads: 64 MB in 3.52 seconds = 18.18 MB/sec
/dev/sda:
Timing buffer-cache reads: 128 MB in 1.23 seconds =104.07 MB/sec
Timing buffered disk reads: 64 MB in 2.01 seconds = 31.84 MB/sec
Vendor: FUJITSU Model: MAJ3364MC Rev: 3702
/dev/sdb:
Timing buffer-cache reads: 128 MB in 1.19 seconds =107.56 MB/sec
Timing buffered disk reads: 64 MB in 1.92 seconds = 33.33 MB/sec
Chip NCR53C895, device id 0xc, revision id 0x2
On PCI bus 0, device 13, function 0, IRQ 10
Synchronous period factor 10, max commands per lun 32
Vendor: IBM Model: DNES-318350W Rev: SA30
/dev/sda:
Timing buffer-cache reads: 128 MB in 0.88 seconds =145.45 MB/sec
Timing buffered disk reads: 64 MB in 3.32 seconds = 19.28 MB/sec
TOSHIBA MK2016GAP
mona@2ch:~$ sudo /sbin/hdparm -tT /dev/hda
Password:
/dev/hda:
Timing buffer-cache reads: 128 MB in 1.04 seconds =123.08 MB/sec
Timing buffered disk reads: 64 MB in 15.71 seconds = 4.07 MB/sec
/dev/hdc:
Timing buffer-cache reads: 128 MB in 0.23 seconds =556.52 MB/sec
Timing buffered disk reads: 64 MB in 1.89 seconds = 33.86 MB/sec
[root@hoge 1002]# cat /proc/ide/hdc/model
IC35L060AVER07-0
速いのでまんぞくしてます。(クラッシュ時のデータ損失が恐い)
/dev/hda:
Model=IBM-DTLA-307020, FwRev=TX3OA50C, SerialNo=YHDYHT8T768
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=40188960
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4 udma5
Timing buffer-cache reads: 128 MB in 1.77 seconds = 72.32 MB/sec
Timing buffered disk reads: 64 MB in 2.60 seconds = 24.62 MB/sec
なにするコマンドか，-tT オプションを含めて
説明希望
俺のにはmanもなかった
No manual entry for hddparm
速いですね。 IDE で 30MB/sec. 越えてるの、はじめて見ました。
>12
いぢめんといて(w
ネタだと思うけど念のため。 man hdparm っす。
Timing buffer-cache reads: 128 MB in 1.16 seconds =110.34 MB/sec
Timing buffered disk reads: 64 MB in 19.87 seconds = 3.22 MB/sec
[root@fireball]:~-> hdparm -tT /dev/hdb
/dev/hdb:
Timing buffer-cache reads: 128 MB in 1.18 seconds =108.47 MB/sec
Timing buffered disk reads: 64 MB in 6.03 seconds = 10.61 MB/sec
速いのか遅いのかようわからんす
/dev/hda:
Model=FUJITSU MPG3307AT, FwRev=02B9, SerialNo=VG13P1201DB7
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=60046560
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
Timing buffer-cache reads: 128 MB in 0.67 seconds =191.04 MB/sec
Timing buffered disk reads: 64 MB in 2.76 seconds = 23.19 MB/sec
SeagateのST380021Aの購入を検討してるんですが、
誰か使ってる人います?
# cat /proc/ide/hda/model
IBM-DTTA-351010
# hdparm /dev/hda
/dev/hda:
multcount = 16 (on)
I/O support = 1 (32-bit)
unmaskirq = 1 (on)
using_dma = 1 (on)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 1232/255/63, sectors = 19807200, start = 0
# hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 2.69 seconds = 47.58 MB/sec
Timing buffered disk reads: 64 MB in 5.35 seconds = 11.96 MB/sec
/dev/hda:
Model=IBM-DTLA-307045, FwRev=TX6OA50C, SerialNo=YMDYMT8V657
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=90069840
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255)
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 1.23 seconds =104.07 MB/sec
Timing buffered disk reads: 64 MB in 1.95 seconds = 32.82 MB/sec
Model=IBM-DPTA-351500, FwRev=P54OA30A, SerialNo=JGYJGT0V480
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=34
BuffType=DualPortCache, BuffSize=425kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=4228907259, LBA=yes, LBAsects=29336832
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3 ATA-4
Kernel Drive Geometry LogicalCHS=1826/255/63 PhysicalCHS=29104/16/63
Timing buffer-cache reads: 128 MB in 10.60 seconds = 12.08 MB/sec
Timing buffered disk reads: 64 MB in 11.88 seconds = 5.39 MB/sec
Model=FUJITSU MPE3273AH, FwRev=EH-A2-27, SerialNo=01005815
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=4228907259, LBA=yes, LBAsects=53359376
IORDY=yes, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
Drive Supports : ATA-1 ATA-2 ATA-3 ATA-4
Kernel Drive Geometry LogicalCHS=3321/255/63 PhysicalCHS=52935/16/63
Timing buffer-cache reads: 128 MB in 2.23 seconds = 57.40 MB/sec
Timing buffered disk reads: 64 MB in 2.96 seconds = 21.62 MB/sec
うは、 udma4 で 5.39 MB/sec. って一体(笑)
>9
今気付いたけど Timing buffer-cache reads が 556.52 MB/sec. って
凄まじい…
/dev/hda:
Model=IBM-DTLA-307030, FwRev=TX4OA50C, SerialNo=YK0YKT7Q703
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=60036480
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
Timing buffer-cache reads: 128 MB in 0.98 seconds =130.61 MB/sec
Timing buffered disk reads: 64 MB in 2.46 seconds = 26.02 MB/sec
BXﾏﾏﾝなんで、ATA33なのだが、悪い結果ではないのかな。
ATA66/100 を Linuxで使うときに ATA33より体感速度は向上する？
Perform timings of cache reads for benchmark and comparison
purposes. For meaningful results, this operation should be repeated
2-3 times on an otherwise inactive system (no other active processes)
with at least a couple of megabytes of free memory. This displays the
speed of reading directly from the Linux buffer cache without disk
access. This measurement is essentially an indication of the
throughput of the processor, cache, and memory of the system under
test. If the -t flag is also specified, then a correction factor based
on the outcome of -T will be incorporated into the result reported for
the -t operation.
-t
Perform timings of device reads for benchmark and comparison purposes.
For meaningful results, this operation should be repeated 2-3 times on
an otherwise inactive system (no other active processes) with at least
a couple of megabytes of free memory. This displays the speed of
reading through the buffer cache to the disk without any prior caching
of data. This measurement is an indication of how fast the drive can
sustain sequential data reads under Linux, without any filesystem
overhead. To ensure accurate measurments, the buffer cache is flushed
during the processing of -t using the BLKFLSBUF ioctl. If the -T flag
is also specified, then a correction factor based on the outcome of -T
will be incorporated into the result reported for the -t operation.
i850/P4/2GHz/ECC RIMMです。バーストは大したことないけど
もしかすると連続したデータ移動にはi850は強いかも
なるほど。どーりで…
さすが世代が違うって感じですねぇ。
# はぁ、ウチもそろそろ速い機械にしたい…
[root@hogehoge]# /sbin/hdparm -tT /dev/hdc
/dev/hdc:
Timing buffer-cache reads: 128 MB in 0.22 seconds =581.82 MB/sec
Timing buffered disk reads: 64 MB in 1.86 seconds = 34.41 MB/sec
[root@hogehoge]# cat /proc/ide/hdc/model
IC35L060AVER07-0
Timing buffer-cache reads: 128 MB in 1.24 seconds =103.23 MB/sec
Timing buffered disk reads: 64 MB in 20.49 seconds = 3.12 MB/sec
これ，もしかして，すごい遅いんですか？
Timing buffer-cache reads: 64 MB in 1.62 seconds =39.51 MB/sec
Timing buffered disk reads: 32 MB in 7.26 seconds = 4.41 MB/sec
bash# cat /proc/ide/hda/model
WDC WD136AA
鬱田市納。
DMA 入れると固まるし。
最近組み立てた AthlonXP 1600+(FSB140 駆動) / PC2100 Registered では、
確か cache read が 200MB/sec. ちょいくらいだったかな。
今は Windows しか入ってないんで、詳細なデータ出せなくてスマヌ。。。
----------
QUANTUM FIREBALL_TM3200A
Timing buffer-cashe reads: 128MB in 3.96 seconds = 32.32MB/sec
Timing buffered disk reads: 64MB in 9.47 seconds = 6.76MB/sec
-------
FMV-5200T5 with P200
IDE drive and driver parameters. Most systems can benefit
from improved performance using a command sequence similar to this:
#!/bin/sh
for d in /proc/ide/hd* ; do
if [ `cat $d/media` = 'disk' ]; then
hdparm -qm8 -qu1 -qc1 -qd1 -qW1 /dev/${d##*/}
elif [ `cat $d/media` = 'cdrom' ]; then
hdparm -qu1 -qd1 /dev/${d##*/}
fi
done
WDC WD181AW
# hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.95 seconds =134.74 MB/sec
Timing buffered disk reads: 64 MB in 3.24 seconds = 19.75 MB/sec
Timing buffer-cache reads: 128 MB in 0.99 seconds =129.29 MB/sec
Timing buffered disk reads:64 MB in 3.99 seconds = 16.04 MB/sec
/proc/sys/vm/max-readahead = 127
/proc/sys/vm/bdflush = "80 0 0 0 6000 18000 90 0 0"
/dev/hda:
Timing buffer-cache reads: 128 MB in 2.03 seconds = 63.05 MB/sec
Timing buffered disk reads: 64 MB in 5.24 seconds = 12.21 MB/sec
IBM-DTTA-351680
/dev/hdd:
Timing buffer-cache reads: 128 MB in 1.99 seconds = 64.32 MB/sec
Timing buffered disk reads: 64 MB in 5.39 seconds = 11.87 MB/sec
Filesystem Size Used Avail Use% Mounted on
/dev/hda5 73G 54G 15G 78% /
/dev/hda1 97M 12M 80M 13% /boot
/dev/hdd1 7.9G 7.1G 802M 91% /Win1
/dev/hdd5 7.9G 7.7G 238M 98% /Win2
/dev/hda:
Timing buffer-cache reads: 128 MB in 1.16 seconds =110.34 MB/sec
Timing buffered disk reads: 64 MB in 5.14 seconds = 12.45 MB/sec
Model=WDC WD1000BB-32CCB0, FwRev=22.04A22, SerialNo=WD-WMA9P1098928
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=195371568
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.74 seconds =172.97 MB/sec
Timing buffered disk reads: 64 MB in 1.69 seconds = 37.87 MB/sec
WDC WD400BB-00AUA1
# hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 1.17 seconds =109.40 MB/sec
Timing buffered disk reads: 64 MB in 3.39 seconds = 18.88 MB/sec
どうやってチューンナップするかな
/dev/hda:
Model=DupliDisk IDE RAID-1 Adapter( 1.25), FwRev=TAH71DP0, SerialNo=
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=3(DualPortCache), BuffSize=2048kB, MaxMultSect=16, MultSect=16
DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=0
CurCHS=16383/16/63, CurSects=4228907259, LBA=yes, LBAsects=20010816
tDMA={min:120,rec:120}, DMA modes: mword0 mword1 *mword2
IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4
UDMA modes: mode0 mode1 *mode2 mode3 mode4
Timing buffer-cache reads: 128 MB in 0.97 seconds =131.96 MB/sec
Timing buffered disk reads: 64 MB in 3.63 seconds = 17.63 MB/sec
ソフトウェアRAIDでミラーしてたときはもっと速かったんだが。
MAXTOR 4K060H3
hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.67 seconds =191.04 MB/sec
Timing buffered disk reads: 64 MB in 1.98 seconds = 32.32 MB/sec
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: QUANTUM Model: ATLAS10K3_18_WLS Rev: 020K
Type: Direct-Access ANSI SCSI revision: 03
hdparm -tT /dev/sda
/dev/sda:
Timing buffer-cache reads: 128 MB in 0.52 seconds =246.15 MB/sec
Timing buffered disk reads: 64 MB in 1.25 seconds = 51.20 MB/sec
/dev/md1:
Timing buffer-cache reads: 128 MB in 0.47 seconds =272.34 MB/sec
Timing buffered disk reads: 64 MB in 0.60 seconds =106.67 MB/sec
７台の RAID5
む、 40 さんは一発で 50MB/sec. 越えてる。。。
/dev/hdb:
Model=ST360021A, FwRev=3.05, SerialNo=3HR04XL1
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=117231408
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 1.28 seconds =100.00 MB/sec
Timing buffered disk reads: 64 MB in 4.23 seconds = 15.13 MB/sec
udma2の制限か? そういや、このモードの最大転送速度って、いくつだっけ。
ST340823A
hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.70 seconds =182.86 MB/sec
Timing buffered disk reads: 64 MB in 4.28 seconds = 14.95 MB/sec
おせぇ。
/dev/hda:
multcount = 16 (on)
I/O support = 1 (32-bit)
unmaskirq = 0 (off)
using_dma = 1 (on)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 1868/255/63, sectors = 30015216, start = 0
cat /proc/ide/hda/model
Maxtor 91531U3
/sbin/hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.91 seconds =140.66 MB/sec
Timing buffered disk reads: 64 MB in 2.59 seconds = 24.71 MB/sec
ん～～ふつうだな・・・
hdparm -tT /dev/hde
/dev/hde:
Timing buffer-cache reads: 128 MB in 1.06 seconds =120.75 MB/sec
Timing buffered disk reads: 64 MB in 2.00 seconds = 32.00 MB/sec
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.46 seconds =278.26 MB/sec
Timing buffered disk reads: 64 MB in 2.72 seconds = 23.53 MB/sec
イマイチやな。P4X266の板。
/dev/hda:
Model=IC35L060AVER07-0, FwRev=ER6OA44A, SerialNo=SZNSZ0P0424
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=120103200
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255)
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 0.28 seconds =457.14 MB/sec
Timing buffered disk reads: 64 MB in 1.78 seconds = 35.96 MB/sec
結構人気？
シリアルコードの見方がわからないので、
60Gの7500rpm？
\16Kで買いましたけど、安い方かな？
漏れもIC35L060AVER07-0。16Kくらいだった。
buffered disk readsが38MB/sec～♪
でもbuffer-cache readsは100MB/sec…。
関係ないけどMozillaで書いてたら逝った…
>む、 40 さんは一発で 50MB/sec. 越えてる。。。
ASC39160/64bitPCI + Atlas10KIII/18GBです。
10000rpmsだけど今まで使ってたIBM DNES309170より
遥かに静か、かつ無茶苦茶速いです。(シーク音は箱に入った
砂をざーっと何かに出すような音ですが、慣れればIBMより
静かです)
なるる。 10000rpm/64bit PCI クラスですか。
うぅ、あちきのような素人には高価で手が出せませぬ。。。
# しかし想像すると恐いかも。。 > 箱から砂を出すような seek 音。。
# hdparm -Tt /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 1.21 seconds =105.79 MB/sec
Timing buffered disk reads: 64 MB in 3.40 seconds = 18.82 MB/sec
# hdparm -i /dev/hda
/dev/hda:
Model=WDC WD400BB-00AUA1, FwRev=18.20D18, SerialNo=WD-WMA6R3967169
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
BuffType=3(DualPortCache), BuffSize=2048kB, MaxMultSect=16, MultSect=off
DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=0
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=78165360
tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4
UDMA modes: mode0 mode1 *mode2 mode3 mode4 mode5
http://linux.ascii24.com/linux/allascii/linuxmag/articles/no_03/p213-217.pdf
(HTMLバージョン)
http://www.google.com/search?q=cache:oKd6CvQO_egC:linux.ascii24.com/linux/allascii/linuxmag/articles/no_03/p213-217.pdf+hdparm&hl=ja&lr=lang_ja
HDD の最適化
http://www.geocities.co.jp/SiliconValley-PaloAlto/5254/hddpfm.html
hdparm を使って IDE ディスクのパフォーマンスを引き出せ
http://libra.higashi.hit-u.ac.jp/manual/hdparm.html
サンクス！
今んとこ１割ほど性能向上中。
よーしパパ チューニングしちゃうぞー
-X 2048
カーネルメイク時間で実測しても何も変化が見られなかったので
チューニングは中止です。
もともとDMAオンにしてたから それ以上は全然・・・
# hdparm -Tt /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.94 seconds =136.17 MB/sec
Timing buffered disk reads: 64 MB in 1.84 seconds = 34.78 MB/sec
# hdparm -i /dev/hda
/dev/hda:
Model=Maxtor 4D040K2, FwRev=DAH017K0, SerialNo=D2H2884E
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80043264
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-6 T13 1410D revision 0 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6
このディスク、容量3GBしかないし、回転数5400もないかもしれんし。
#/sbin/hdparm -a128 -c1 -d1 -m16 -tT -f -i /dev/hda
/dev/hda:
setting fs readahead to 128
setting 32-bit I/O support flag to 1
setting multcount to 16
setting using_dma to 1 (on)
multcount = 16 (on)
I/O support = 1 (32-bit)
using_dma = 1 (on)
readahead = 128 (on)
Model=WDC AC33200L, FwRev=32.41N35, SerialNo=WD-WT3720272174
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=6296/16/63, TrkSize=57600, SectSize=600, ECCbytes=22
BuffType=DualPortCache, BuffSize=256kB, MaxMultSect=16, MultSect=16
CurCHS=6296/16/63, CurSects=6346368, LBA=yes, LBAsects=6346368
IORDY=on/off, tPIO={min:160,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 *mdma2 udma0 udma1 udma2
Timing buffer-cache reads: 128 MB in 3.25 seconds = 39.38 MB/sec
Timing buffered disk reads: 64 MB in 7.34 seconds = 8.72 MB/sec
/dev/hdc:
Timing buffer-cache reads: 128 MB in 0.61 seconds =209.84 MB/sec
Timing buffered disk reads: 64 MB in 1.71 seconds = 37.43 MB/sec
やっと、udma5が使えるようになりました。
気づかなかったけど、VIA VT82* South Bridge 使ってる場合、
RedHat7.2、付属のドライバ(via82cxxx.o)ではudma3/4/5が使えないみたい。
より新しいカーネルのドライバを使うと良いと思います。
(RedHat7.2のカーネルソース持ってる人は、
linux/drivers/ide/via82cxxx.c の436行目、
via_80w = 0;
っていうのをコメントアウトするとうまくいくかもしれません。
見たかんじ、これがケーブルの検出を無効にしてるみたいなので…
責任は持てませんが、私の場合はうまく動いるみたいです)
> hdparm -tT /dev/sda
/dev/sda:
Timing buffer-cache reads: 128 MB in 1.14 seconds =112.28 MB/sec
Timing buffered disk reads: 64 MB in 4.47 seconds = 14.32 MB/sec
駄無なので速いのか遅いのか分かりません(w
最近このﾏｯｼｰﾝは全てSCSIにしてみたんだが
取りあえずIDEで組んでいた時よりは安定はしてる。
/dev/hda:
Model=ST380021A, FwRev=3.05, SerialNo=3HV07CBR
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=156301488
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 0.54 seconds =237.04 MB/sec
Timing buffered disk reads: 64 MB in 1.79 seconds = 35.75 MB/sec
ヤフーオークションで、凄い人気商品、発見！！！
「高性能ビデオスタビライザー」↓
http://user.auctions.yahoo.co.jp/jp/user/NEO_UURONNTYA
ヤフーオークション内では、現在、このオークション
の話題で、持ちきりです。
Model=IC25N020ATCS04-0, FwRev=CA2OA70A, SerialNo=隠してもしょうがないけど。
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=3(DualPortCache), BuffSize=1768kB, MaxMultSect=16, MultSect=16
DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=2
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=39070080
tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
IORDY=on/off, tPIO={min:240,w/IORDY:120}, PIO modes: mode3 mode4
UDMA modes: mode0 mode1 *mode2 mode3 mode4 mode5
Timing buffer-cache reads: 128 MB in 1.10 seconds =116.36 MB/sec
Timing buffered disk reads: 64 MB in 3.24 seconds = 19.75 MB/sec
ATA33じゃあこんなもんか。
DJSA220に比べれば、むっちゃ静か。アクセス音は聞こえるけどね。
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: COMPAQ Model: BB01823469 Rev: 3B07
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: QUANTUM Model: ATLAS10K3_36_WLS Rev: 020K
Type: Direct-Access ANSI SCSI revision: 03
/dev/sda:
Timing buffer-cache reads: 128 MB in 0.77 seconds =166.23 MB/sec
Timing buffered disk reads: 64 MB in 2.48 seconds = 25.81 MB/sec
/dev/sdc:
Timing buffer-cache reads: 128 MB in 0.77 seconds =166.23 MB/sec
Timing buffered disk reads: 64 MB in 1.84 seconds = 34.78 MB/sec
まあ、こんなもんか。
# cat scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: SEAGATE Model: ST34371N Rev: 0484
Type: Direct-Access ANSI SCSI revision: 02
/dev/sda:
Timing buffer-cache reads: 128 MB in 11.21 seconds = 11.42 MB/sec
Timing buffered disk reads: 64 MB in 31.75 seconds = 2.02 MB/sec
……笑うしか無い
Timing buffered disk reads: 64 MB in 4.61 seconds = 13.88 MB/sec
2年以上前の10GBハードディスク．
RH7.2付属のカーネルドライバソース書き換えですが、
この変更を行っても検出がうまくいくのでは無いようです、
無条件？で、Cable Type: 80wになりますので、やっぱり新しいのを
使ったほうがいいようです。
/dev/hda:
Model=ST340016A, FwRev=3.10, SerialNo=3HS1RGAP
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=4047/16/255, CurSects=-217054981, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 0.45 seconds =284.44 MB/sec
Timing buffered disk reads: 64 MB in 1.58 seconds = 40.51 MB/sec
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6
Timing buffer-cache reads: 128 MB in 0.70 seconds =182.86 MB/sec
Timing buffered disk reads: 64 MB in 2.73 seconds = 23.44 MB/sec
こんな感じなんですけど、もっと速くなりますか？
/dev/hda:
Model=IBM-DJSA-220, FwRev=JS4OAC3A, SerialNo=44V44N87277
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=1874kB, MaxMultSect=16, MultSect=16
CurCHS=17475/15/63, CurSects=16513875, LBA=yes, LBAsects=39070080
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4
AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 2.71 seconds = 47.23 MB/sec
Timing buffered disk reads: 64 MB in 4.43 seconds = 14.45 MB/sec
おれのnote PC すげーおそいぞ。なんでだ？
サウスにあわせて、カーネルいじってみるとか…
汎用カーネルは遅いような気がするのはｵﾚだけか？
>>71 メーカは？って言うか、サウスは？
440MXでももう少し出ると思うんだが…
ってわけで、とりあえず>>54を参照すべし
> サウスにあわせて、カーネルいじってみるとか…
いじるってchipsetで選ぶだけですよね？
必要最低限のカーネルにしてるんですけどねぇ。
buffer-cacheの転送速度が全然違いますがな
メモリとプロセッサの差じゃないですかね
Pen3-1.13GHzなノート,i830MGチップセット
# hdparm -itT /dev/hda
/dev/hda:
Model=TOSHIBA MK4018GAP, FwRev=M0.03 A, SerialNo=12R64684T
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=46
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=78140160
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: unknown setting
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 0.65 seconds =196.92 MB/sec
Timing buffered disk reads: 64 MB in 2.95 seconds = 21.69 MB/sec
ちなみに AthronXP 1700+ +K7S5A(133/133) +DDR256x2 +BarraIV40G
う～ん。読み込み自体はそこまで変わらないと思ってたYo!
けど、BarraIVとU6って、7200/5400rpmぐらいしか違わないような…
11.25 しかでなかった。
# 2年以上昔の IBM のほうが 16.89 で速い。
どうやっても 16MB/s あたりで頭打ちになる。
over 20MB/s ってどんな環境で出るの?
ATA66 で使ってるけど、ATA100 だと出る?
5400rpm だとダメで 7200rpm だと出る?
CPU とかﾁﾌﾟｾﾄの情報もｷﾎﾞﾝ
Model=MAXTOR 4K080H4, FwRev=A08.1500, SerialNo=374118327334
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=32256, SectSize=21298, ECCbytes=4
BuffType=DualPortCache, BuffSize=2000kB, MaxMultSect=16, MultSect=16
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=156301487
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2
AdvancedPM=no WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 0.78 seconds =164.10 MB/sec
Timing buffered disk reads: 64 MB in 4.17 seconds = 15.35 MB/sec
/dev/hdc:
Model=IBM-DTLA-305040, FwRev=TW4OA60A, SerialNo=YJEYJ0A8975
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=380kB, MaxMultSect=16, MultSect=16
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=80418240
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 0.79 seconds =162.03 MB/sec
Timing buffered disk reads: 64 MB in 4.05 seconds = 15.80 MB/sec
/dev/hda:
Model=IBM-DTLA-305030, FwRev=TW3OA60A, SerialNo=YG0YGT0A157
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=380kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=60036480
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255)
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 0.82 seconds =156.10 MB/sec
Timing buffered disk reads: 64 MB in 2.84 seconds = 22.54 MB/sec
あおぺんのブックベアボンですけどね。ぺんほーの。北森は載らないですが
1.7Gは割と普通に使用可能です。
Model=FUJITSU MPG3409AT E, FwRev=82B9, SerialNo=VH06T150CWSM
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=80063424
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4 udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 0.82 seconds =156.10 MB/sec
Timing buffered disk reads: 64 MB in 2.32 seconds = 27.59 MB/sec
PIII(650)+vt82c686aだとこんな感じ
>>79
chipsetが本当に586Bだったらその辺が限界かもしれず
しかも、ATA66になってないよ
MPG3409AT-EF も持ってたけど、やっぱり 15MB/s 位だったな。
やっぱりサウスの責任かなぁ。
CPU は k6-III と Pen3-700 で hdparm -t の数値ぜんぜん
変わんなかったんだよね(サウスは一緒)。だから CPU は多分かんけいない。
hdparm -I で見ると /dev/hdc は udma4 に * が付くので ATA66
になってると思う。/dev/hda のほうはケーブルが ATA33 用なので
udma2 のままでいい。
実は ATA100 用ケーブル繋いだ /dev/hdc を udma4 で使ってみて
ぜんぜん改善しなかったので /dev/hda のほうを udma4 化する気力を
なくしてる ...
WDC WD800BB-53BSA0
hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.41 seconds =312.20 MB/sec
Timing buffered disk reads: 64 MB in 2.07 seconds = 30.92 MB/sec
はやいっすかね？満足してます。
Model=IC35L040AVVA07-0, FwRev=VA2OA52A, SerialNo=VNC202A2GXH4ZA
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1863kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80418240
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4 udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 0.74 seconds =172.97 MB/sec
Timing buffered disk reads: 64 MB in 1.46 seconds = 43.84 MB/sec
Model=ST340016A, FwRev=3.75, SerialNo=3HS460E5
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 0.82 seconds =156.10 MB/sec
Timing buffered disk reads: 64 MB in 1.64 seconds = 39.02 MB/sec
PCスペックは 青ペンのAX6BC TypeR +Cel900(OCで1008Mhz)+ 384MB
玄人指向ATA100-PCI さしてやってまふ。
こんなもんでしょうか?
Model=TOSHIBA MK6014MAP, FwRev=N2.10 A, SerialNo=207A4366T
Config={ Fixed }
RawCHS=12416/15/63, TrkSize=0, SectSize=0, ECCbytes=46
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=off
CurCHS=12416/15/63, CurSects=11733120, LBA=yes, LBAsects=11733120
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4
Timing buffer-cache reads: 128 MB in 1.59 seconds = 80.50 MB/sec
Timing buffered disk reads: 64 MB in 18.95 seconds = 3.38 MB/sec
3年前のNotePC。まだまだ鯖現役。
/dev/hda:
Model=Maxtor 5T030H3, FwRev=TAH71DP0, SerialNo=T3H00YAC
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=60030432
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
AdvancedPM=yes: disabled (255)
Drive Supports : ATA/ATAPI-6 T13 1410D revision 0 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6
Timing buffer-cache reads: 128 MB in 0.92 seconds =139.13 MB/sec
Timing buffered disk reads: 64 MB in 2.97 seconds = 21.55 MB/secB/sec
こんなもんか。
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 0.47 seconds =272.34 MB/sec
Timing buffered disk reads: 64 MB in 1.57 seconds = 40.76 MB/sec
K7S5A: SiS735 です。
昨日まで >>69, 86 さんみたいな速度がでなくて、やはり SiS か…
と鬱でしたが、原因はケーブルのほうでした。ごめんな > SiS
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5
Kernel Drive Geometry LogicalCHS=77545/16/63 PhysicalCHS=77545/16/63
Timing buffer-cache reads: 128 MB in 1.93 seconds = 66.32 MB/sec
Timing buffered disk reads: 64 MB in 5.23 seconds = 12.24 MB/sec
Promise Ultra 100 TX2をKernel 2.2.20にパッチを当てて使ってます。
ATA-5で動いているのになぜか遅い。
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80418240
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 0.64 seconds =200.00 MB/sec
Timing buffered disk reads: 64 MB in 1.93 seconds = 33.16 MB/sec
kernel2.4.18-686-smp VP_IDE: VIA vt82c686bです
オプションはhdparm -X68 -d1 -c1
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1863kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=120103200
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1: 2 3 4 5
Timing buffer-cache reads: 128 MB in 0.53 seconds =241.51 MB/sec
Timing buffered disk reads: 64 MB in 1.42 seconds = 45.07 MB/sec
SuSE8.1 KT266Aです。
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5
Timing buffer-cache reads: 128 MB in 0.31 seconds =407.08 MB/sec
Timing buffered disk reads: 64 MB in 1.58 seconds = 40.50 MB/sec
Redhat7.3 P4S533(south SiS646)
HDDをつけても、PCI66MHzのスロットにプロミス社のU133DMAカードを挿して、
ATAの高速ディスクをいろいろ取り替えてみても、hdparm -t の値が、
どれも 40MB/s を越えません。どこにボトルネックがあるのでしょうか？
Model=IBM-DTTA-371010, FwRev=T77OA73A, SerialNo=WL0WLFA9614
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=34
BuffType=DualPortCache, BuffSize=465kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=19746720
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2 udma0 udma1 udma2
AdvancedPM=no WriteCache=enabled
Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3 ATA-4
Timing buffer-cache reads: 128 MB in 2.67 seconds = 47.94 MB/sec
Timing buffered disk reads: 64 MB in 6.41 seconds = 9.98 MB/sec
/dev/hdb:
Model=Maxtor 33073U4, FwRev=BAC51KJ0, SerialNo=N40AEPGC
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=512kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=58633344
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 *mdma2 udma0 udma1 udma2 udma3 udma4
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-6 T13 1410D revision 0 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6
Timing buffer-cache reads: 128 MB in 2.65 seconds = 48.30 MB/sec
Timing buffered disk reads: 64 MB in 6.83 seconds = 9.37 MB/sec
五年前のPCだからへろへろだ。
1.5MB/S 程度しかでなかったことが懐かしい。
Model=Maxtor 90648D3, FwRev=GAS54812, SerialNo=A3HZ8DJC
Config={ Fixed }
RawCHS=12556/16/63, TrkSize=0, SectSize=0, ECCbytes=29
BuffType=DualPortCache, BuffSize=512kB, MaxMultSect=16, MultSect=16
CurCHS=12556/16/63, CurSects=12656448, LBA=yes, LBAsects=12656448
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2
AdvancedPM=no WriteCache=enabled
Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3 ATA-4
Timing buffer-cache reads: 128 MB in 1.08 seconds =118.52 MB/sec
Timing buffered disk reads: 64 MB in 4.65 seconds = 13.76 MB/sec
3年前のものだから、こんなもんか…
最近のは一発でもdisk readが50MB/sec越えるらしいでつね…
TOP カテ一覧 スレ一覧 2ch元 削除依頼 ▲
何食べ、飲みながらlinuxマシンに向かってる？ (148)
オープンソースを他の産業にも広めよう (184)
CentOSとAMDのCPUを絡めて話したい人のスレ (109)
kubuntu (572)
KDEスレ Part 9 (373)
KDEスレ Part 9 (373)
--log9.info------------------
ぷちます！-プチ・アイドルマスター- 10あふぅ (519)
最終兵器彼女 十六戦目 (470)
絶対防衛レヴィアタン 絶対9スレ目だもん！ (598)
世界名作劇場 レ・ミゼラブル 少女コゼット part28 (970)
ちはやふる 68首目 (871)
境界線上のホライゾンⅡ 271限目 (611)
【米は】SAMURAI7 二十六俵目【サムライのもの】 (975)
BLOOD-C ギモーブ63個目 (575)
マクロスF（フロンティア）part556 (427)
真・恋姫†無双～乙女大乱～ 71メンマ (678)
BLUE DROP ～天使達の戯曲～19 (142)
ロケットガール 11号機 (652)
TARI TARI 第85小節 (189)
黄昏乙女×アムネジア 23 (120)
コードギアスは製作も信者もキチガイの産廃アニメ215 (743)
【TEST】IDテストスレッド＠アニメ２板17 (772)
--log55.com------------------
田母神 智子 Part.1
□ □ □ 伽奈 part2 □ □ □
【デブな男とは】長谷川理恵【付き合えません】
遠藤裕美
【モデル事務所】スマイルモンキー5【子役】
【主食はお菓子♪】gehaけいこ【ﾃﾞｨｱﾏﾝﾃ店長♪】
【RQ】 矢野涼子
山川未央 mio y*5